BETCO Genie B Specifications

1GENIE™ B APS14” All Purpose Automatic ScrubberE83039-001001 Brown Avenue • Toledo, Ohio 43607-0127 Customer Service: 888-GO-BETCO • Fax: 800-44

1011. SOLUTION TANKThe recovery tank must be completely emptied each time the solution tank is filled.Ensure the cap is correctly threaded into the sol

1113. RECOVERY TANKMake sure the recovery tank is empty, otherwise, empty it completely. Check that it is properly secured to the handle tube and tha

121. MACHINE OPERATIONBefore installing the tanks, it is necessary to carry out the following operations:1. Open the two rear latches to the battery

1313. RECOVERY TANKTo properly turn off the machine after use or before performing any maintenance:1. Turn off the solution control switch (3).2.

141. CLEANING THE RECOVERY TANK1. Disconnect the vacuum hoses from the recovery tank lid.2. Detach the recovery tank from the handle tube.3. Remove

153. REPLACING THE SQUEEGEE BLADESExamine the condition of the squeegee blades. Replace as necessary. To replace the blades:A. Lift the squeegee.B.

161. CLEANING THE SQUEEGEE HOSECheck the squeegee hose for blockage if the suction is insufficient and at peri-odic intervals. To clean the hose:A. Re

171. ELECTRICAL SYSTEM SAFETYThe machine is equipped with self-resetting thermal safety fuses located in the electric box beneath the solution tank.

18POLYPROPYLENE BRUSHES (PPL)These are used on all types of floors and offer good wear resistance.PAD DRIVERSPad driver and an floor pad is recommended

19

2TABLE OF CONTENTSRECEIVING THE MACHINE... 3TECHNICAL SPECIFICATIONS ...

20BRUSH DECK PARTS DIAGRAM3943144746294544323653031310382615212372512634167174151819112427229252835331813414249232048

21BRUSH DECK PARTS LISTING 1 E81530 Spring, 17, 5x2, 5x69 mm 1 2 E82845 Spacer 3 3 E82844 Clutch Plate 1 4 E20503 Spacer 1 5 E88228 Bu

22SQUEEGEE SYSTEM PARTS DIAGRAM518718161511236417172129101112111413

23SQUEEGEE SYSTEM PARTS LISTING 1 E81815 Squeegee Vacuum Adapter 1 2 E81897 Bushing 1 3 E85792 Squeegee Shoe 1 4 E81753 Knob M5 6 5 E

24SQUEEGEE YOKE PARTS DIAGRAM1325110731114861249

25SQUEEGEE YOKE PARTS LISTING 1 E87971 Squeegee Yoke Arm 1 2 E86153 Squeegee Yoke 1 3 E82839 Squeegee Yoke Pivot 1 4 E86263 Oval Hd Phi

26MAIN FRAME PARTS DIAGRAM3826133627192427144823529221711621103017223618233333431254241401243285321120157639212644937

27MAIN FRAME PARTS LISTING 1 E20272 Bushing 2 2 E20020 Hex Lug 1 3 E86269 Bushing 2 4 E20050 Protective Trim Edging 1 5 E20587 Clamp

28SOLUTION AND RECOVERY TANKS PARTS DIAGRAM1352781161014139124152.92.32.12.52.82.62.72.42.2

29SOLUTION AND RECOVERY TANKS PARTS LISTING 1 E81532 Hose, Vacuum 29 D x 1250 L 1 2 E81534 Recovery Tank Cap ASM 1 2.1 E82853 Filter Fla

3Immediately check, when receiving the machine, that all the materials indicated on delivery documents have been received and also that the machine ha

30CONTROL HANDLE PARTS DIAGRAM28123052517223927327183229436110268152411621313620331934321314227.87.47.57.97.37.17.27.77.67.87.5353711384039

31CONTROL HANDLE PARTS LISTING 1 E85770 High Hex Nut M6x13 Zinc 4 2 E81793 Spring Pin M6x12 Zinc 3 3 E20273 Connector Tube 1 4 E20620 H

32ELECTRIC SYSTEM PARTS DIAGRAM4721635

33ELECTRIC SYSTEM PARTS LISTING 1 E83547 M6x16 Bolt, Zinc Hex Head 1 2 E83550 Nyloc Hex Nut, M6 Zinc 1 3 E82761 Washer 6x12x1.6 1 4 E817

34BATTERY CHARGER DIAGRAM11427971061713241262131851512201625817232281411124221919143029315

35ELECTRICAL LISTING 1 E20272 Bushing 2 2 E20579 Protective Trim Edging 2 3 E20050 Protective Trim Edging 1 4 E20393 Screw, Pan Hd Phil

36ACCESSORIES DIAGRAM564213713” Pad14” PadMedium BrushSTD General BrushHeavy Brush8Clutch Plate

37ACCESSORIES LISTING 1 E82367 Center Lock 1 2 E82438 Power Cord 1 3 E82408 Pad Driver 1 4 E88140 Pad Holder 14" STD 1 5 E83863

38

39

4Working width in (mm) 13.8 (350)Rear squeegee width in (mm) 17.3 (440)Work capacity ft2/h ( m2/h) 11,300 (1050)Water consumption g/m2 -Batter

4092156-94 March14E1001 Brown Avenue • Toledo, Ohio 43607-0127 Customer Service: 888-GO-BETCO • Fax: 800-445-5056 • Technical Service: 877-856-

5The regulations below must be carefully followed in order to avoid harm to the operator and damage to the machine.• Read the labels on the machine c

61. HANDLING THE PACKED MACHINENo more than two boxes can be stacked.Total weight is 150 lbs. per box.Overall dimensions are: A: 19.7 in (500 mm) B:

74. INSTALLING AND CONNECTING THE BATTERIESThe machine is supplied with an on-board battery charger and a sealed main-tenance free battery. If a batt

86. BATTERY MAINTENANCE AND DISPOSALFor maintenance and recharging, follow the instructions provided by the battery manufacturer or only use factory s

98. BATTERY DISCHARGE INDICATORThe battery indicator is digital with 4 fixed positions and a flashing signal. The numbers that appear on the display re